英文字典,中文字典,查询,解释,review.php


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       


安装中文字典英文字典辞典工具!

安装中文字典英文字典辞典工具!










  • 10d Common Nail - Structural engineering general discussion - Eng-Tips
    As PMR06 says, there are many different nail sizes for the given name I usually will call out the nail as 8d (2-1 2" x 131") to help clarify specifically which nail I am talking about Upvote 0 Downvote
  • Wood Diaphragm Nail Slip Maximum Load | Eng-Tips
    for 10d common nails the maximum fastener load for calculating nail slip is 260lb (this is for deflection, so ASD loads) If you calculate the fastener strength for a 10d nail connecting plywood into framing (assuming the plywood's specific gravity is 0 5 and framing also), you get the following load from Table 11Q in NDS 2005 multiplied by 1 6
  • Nails and Horizontal Shear 1 - Eng-Tips
    The proper nail is a 10D short (2 1 4 quot, the framing members must be a nominal 3 quot; width (2 1 2 quot; dressed) 3 quot; members are only required if the nailing schedule is 3 quot; o c or closer with 10D nails 8D nails are allowed for 3 quot; nailing into 2X When the need arises for blocked diaphragms with 2 quot;, 2 1 2 quot; or 3
  • Nails in Pull-Out - Welding, Bonding Fastener engineering
    For example, a 10d nail (0 128 inch dia = 3 25 mm dia) in a Douglas Fir North wood (S G = 0 49) would yield a pull out capacity (allowable) of 26 lbs (115 N) This value would have to be multiplied by a duration of load factor (depends on the sustained time of the load) as well as a few other factors pertaining to wet service or temperature
  • 2021 SDPWS - No Short Nails Allowed 1 - Eng-Tips
    However, the inclusion of "Minimum Fastener Penetration" in the tables led to the interpretation that a 10d short nail with 0 148" diameter was adequate as long as the penetration was met Perhaps it's regional, but many firms in CA have notes in their drawings that explicitly permit short nails for sheathing applications
  • 16d Common Nails - Nail Gun? - Structural engineering general . . .
    Recently we have been getting RFI's and substitution requests regarding 16d common nails (0 162x3 1 2) not having nail gun options Typically they are asking to use 16d Sinker nails (0 148x3 1 4) which is roughly equivalent to a 10d common for capacity 16d common nails have been used for as
  • Roof Diaphragm - Sheathing over T amp;G decking - Eng-Tips
    That sounds like a good idea but I don't get how you show the reduced P is stronger than the 8d nail with 1 3 8" I agree it's more than the 6d nail at 1 1 4" But with a 71 reduction factor (1 0625 1 5) the reduction takes you below the 8d values which are roughly 84% of the 10d values
  • Zip-R - Structural engineering general discussion | Page 2 - Eng-Tips
    I have a customer wanting to use R12 Zip-R sheathing (2" foam 1 2" OSB) I hate this crap Anyhow, the specs require 0 131"Ø nails to penetrate 1 1 2" into the framing That means they need a 4" long, 10d nail Does that even exist and for a gun?


















中文字典-英文字典  2005-2009