英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字,中文词皆可:


请选择你想看的字典辞典:
单词字典翻译
vitrinus查看 vitrinus 在百度字典中的解释百度英翻中〔查看〕
vitrinus查看 vitrinus 在Google字典中的解释Google英翻中〔查看〕
vitrinus查看 vitrinus 在Yahoo字典中的解释Yahoo英翻中〔查看〕





安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Finishing drywall: How do I finish over screws that refuse to recess . . .
    I could remove the offending screws, drill out a wider hole, and screw them back in, but I don't want to deteriorate the integrity of the grab I'd like to finish over them so that the wall is smooth What do I do, tape over them? Use an extra-thick layer of mud? Eh?
  • How do I consistently drive drywall screws to the correct depth?
    Is there a special technique or tool for consistently placing drywall screws correctly? I'm using a standard Dewalt variable speed drill DWD115K (with no auto-stop mechanism) so I'm usually paranoi
  • Are these drywall screws driven too deep into the sheet?
    The other problem with driving drywall screws with a regular #2 Phillips bit is that screws driven too deep will not have the holding power and the screws will pull through, leaving the sheet unattached to the studs This is especially important when hanging rock on ceilings These are the proper tools and bits
  • What is the weight capacity of your typical 2 1 2 drywall screw when . . .
    The screws themselves aren't suspended over a distance, they are tightly attached between the clip stud and drywall channel If the screw went through the drywall, 1 2" of air, into the stud, and was the only thing holding the drywall up, you'd be in trouble
  • screws - hole too big for anchor but anchor is still stuck - Home . . .
    It's hard to tell from your strangely-lit photo, but I think that's an expanding anchor The four wings expand when you tighten the screw, to grab the back of the wall If the anchor is too small for the hole or the screw too small for the anchor, it might expand a little then start rotating : ( Removing it by pulling will damage the wall Since you are able to pull the plug out slightly, you
  • What are the implications of driving a drywall screw too far into the . . .
    I did so many things wrong that I've since learned from, but the first mistakes are still glaringly obvious, one of which being how I drove screws too far into drywall Some do more than break the paper and actually sink into the sheet by as much as 1 8" I've read that this can keep the wall from being stable
  • Recommend attachment for a drill driver for drywall screws
    I know there exist special 'screw guns' which are used to install drywall sheets and ensure that the sheets won't be crushed when driving screws Do there exist special attachments which are instal
  • What do I do if drywall screws wont penetrate the studs?
    If the drywall pops, use two or more screws 2-3" apart, slowly sinking each one to distribute the load If the heads pop off (tension), use the same procedure only this time, run the screw backwards until it hits the stud, creating a relief This countersinks the drywall and will help you set the screws with a poor drill or unhappy hard wood
  • Drywall surrounding vent no longer supports screws;
    Screws that normally fix the vent in place can't do their job anymore The drywall has crumbled to the point that the tapped hole for the screw lacks a boundary with the duct (Picture attached ) P
  • Drywall screws visible - Home Improvement Stack Exchange
    We have noticed in our new home (which was renovated quite poorly by the previous owner), that the drywall screws are visible We can visibly see where every stud is Does this simply require sand





中文字典-英文字典  2005-2009