英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

protrusion    
n. 推出,突出,露出

推出,突出,露出

protrusion
n 1: something that bulges out or is protuberant or projects
from its surroundings; "the gun in his pocket made an
obvious bulge"; "the hump of a camel"; "he stood on the
rocky prominence"; "the occipital protuberance was well
developed"; "the bony excrescence between its horns" [synonym:
{bulge}, {bump}, {hump}, {swelling}, {gibbosity},
{gibbousness}, {jut}, {prominence}, {protuberance},
{protrusion}, {extrusion}, {excrescence}]
2: the act of projecting out from something [synonym: {protrusion},
{projection}, {jut}, {jutting}]

Protrusion \Pro*tru"sion\, n.
1. The act of protruding or thrusting forward, or beyond the
usual limit.
[1913 Webster]

2. The state of being protruded, or thrust forward.
[1913 Webster]


请选择你想看的字典辞典：
单词字典翻译
protrusion查看　protrusion　在百度字典中的解释百度英翻中〔查看〕
protrusion查看　protrusion　在Google字典中的解释Google英翻中〔查看〕
protrusion查看　protrusion　在Yahoo字典中的解释Yahoo英翻中〔查看〕

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Piston protrusion below specs | Cummins Diesel Forum
    I measured my piston protrusion on my 12v and my protrusion is way below specs I am at 016 and my other pistons are about the same and or slightly lower
  • Piston protrusion specs,,,Im so confused | Cummins Diesel Forum
    I'm in the process of putting together a 12 valve for a conversion project The block needed a 0 020 overbore and I waited for like four months for some Mahle motorsport performance cast pistons What I don't understand is how much piston protrusion is acceptable before a thicker head gasket is
  • Piston Protrusion Over Spec. What Head Gasket?
    The problem: I measured my piston protrusion over the wrist pin as the manual instructs and had a couple of pistons that are a bit out of spec coming in with a total protrusion of 0 022" The service manual says that min protrusion is 0 006" and max is 0 019" and if you are outside this range then you have a problem
  • Headgasket thickness PTV compression HELP | Cummins Diesel Forum
    For piston protrusion I have tried to find exact figures for my 97 I read one thread that posted 0 024-0 028 protrusion is oem spec Mine being 030- 034 if I went with a 010 over head gasket I'm assuming I would lose a little bit of compression across the board but also increase my PTV
  • Piston protrusion question | Cummins Diesel Forum
    Piston protrusion question Jump to Latest 8 6K views 5 replies 3 participants last post by Strokerforlife Feb 2, 2017 S
  • Protrusion, CR | Cummins Diesel Forum
    Currently, the protrusion is at the level of 0 035 (0 9 mm) What should I do? A thicker gasket (hardly available in Europe) and a protrusion of 0 025 or lower the top of the piston by 0 005 and keep the protrusion at 0 030? Can these pistons be machined at all? Thanks for help
  • Piston protrusion | Cummins Diesel Forum
    Hey I just finished installing my pistons and was going through to check the protrusion and number 1 was in aspect 25 thousands but the rest where all at 35 thousands Im not sure what to do about this should I run the 10 thousands over head gasket or try to fix it The block was cleaned up at
  • Head Gasket kit-which gasket is thicker? | Cummins Diesel Forum
    The gasket thickness is determined by piston protrusion above the block Measure the protrusion any thing above 030 use the thicker gasket marked by two holes anything les use the thinner one marked by one hole
  • Injector Tip Protrusion. . . Risk of hitting pistons?
    Is there any risk of the injector tips being hit by the piston if too thin of seal washers are installed? Are there any other risks? Reason I ask is because upon reassembly of changing my head gasket, I checked the tip protrusion on each injector before putting the head in They were all WAY
  • Just a fyi with Genuine Cummings head gaskets - Dodge Cummins Diesel Forum
    Using the average piston protrusion recorded earlier, determine which head gasket is needed from the following table: Head Gasket Determination Average Piston Protrusion Head Gasket Grade >= 0 30 mm [0 012 in] Thick < 0 30 mm [0 012 in] Thin The head gaskets for 5 9 L engines without EGR and 5 9 L engines with EGR with oversize pistons or repair





中文字典-英文字典  2005-2009