英文字典中文字典


英文字典中文字典51ZiDian.com



中文字典辞典   英文字典 a   b   c   d   e   f   g   h   i   j   k   l   m   n   o   p   q   r   s   t   u   v   w   x   y   z       







请输入英文单字，中文词皆可：

安装中文字典英文字典查询工具!


中文字典英文字典工具:
选择颜色:
输入中英文单字

































































英文字典中文字典相关资料:


  • Cast Boolits
    This is the dedicated cast bullet forum!Please note that if you are using a high risk VPN to register, your profile may be placed in a banned status If this is your first visit, be sure to check out the FAQ You will be required to register before you can post: click the register link above to proceed To start viewing messages, select the forum that you want to visit from the selection below
  • Straight vs tapered - Cast Boolits
    I know that hulls are identified as either straight or tapered wall Other than the published data, USE ------> Hull - Primer - Power - Wad - Payload Why aren't the wads classified as straight or tapered? For me, this is the most confusing part of shot shell loading, logic would tell you that a straight wall hull needs a straight wall wad correct? Thoughts???
  • My (bad) experience with Walters wads. - Page 2 - Cast Boolits
    John got me on poly wads too Have done business with him for years, but the last bag of poly wads I got were horrible, punched 2 at a time and all stuck together, ordere 44 rifle, 451 diameter, came at 457 To small for 45, too large for 45's
  • Felt greased wad under bullet - Cast Boolits
    I understand the use of greased felt wads with BP and the need to have uniform powder compression in that arena —- why didn’t I use black? I searched all over the county for proper ingredients for Paul Matthews BP bullet lube and finally had to order from Amazon…
  • A wad is a wad is a wad? - Cast Boolits
    The wads are fine for what they are---light target wads for Rem Win tapered hulls But, I think they became pretty successful at one point, so powder companies started publishing data for straight-wall hulls and heavier loads, and that's where the trouble started
  • Winchester Red wads WAA12R [Archive] - Cast Boolits
    the claybuster wads do not work with slugs, they have a taper on the petals and the slug, both lee and lyman cut the petals off the plastic is also really soft and even with lead shot over 2 dram eq pyrodex loads, it blows the gas seal i have about 10 bags of the real good winchester wads and 450 of the claybuster junk
  • ? on Alcan Flite-Max - Cast Boolits
    ? on Alcan Flite-Max Am wondering if anyone can tell me if Alcan put their 3 8 in Feltan-Bluestreak fiber wads inside the Flite-Max No 2 wad? These are a light blue in color
  • homemade wads? - Cast Boolits
    For cushion wads I made up cutters that look like regular wad cutters but have a 1 2" stem that will fit in a drill press and one side just slightly beyond half way is milled away With the drill press running at a very low speed, I cut wads from 1 2" celotex ( some lumber yards still carry it ) then using a couple of coffee cans for kind of a double boiler, I quickly soak the wads in melted
  • Hull Dimensions - Cast Boolits
    I measured all the wads I have with a set of calipers and built a table so I can compare using the manuals Not precision but helps Hard to do with hulls The sad part is that the manufacturers have the dimensions on drawings to make their dies for forming the wads Easy to publish and no great secret Too easy to reverse engineer Same with hull manufacturers Would help us, the customer out
  • wads for 20 gauge magtech brass shells - Cast Boolits
    I have been looking around and everybody seems to be out of one or more of the wads for 20 gauge magtech brass shells for black powder According to manufacturer suggested wads it should be a circle fly 18 gauge 125" overpower card, with a circle fly 18 gauge 500" fiber cushion wad, and a circle fly 17 gauge 025" overshot card No one source (track of the wolf, brownells, midwayusa





中文字典-英文字典  2005-2009